邮箱:xiamen2018@foxmail.com

手机/微信/WhatsApp

+86 15270269218

Traco Power TIS 600-124 工业电源

发布时间:2024-06-13人气:
  • Traco Power TIS 600-124 工业电源
  • Traco Power TIS 600-124 工业电源
  • Traco Power TIS 600-124 工业电源
  • Traco Power TIS 600-124 工业电源

TIS 600-124 工业电源一款工业级AC-DC导轨式开关电源,由TRACO Power设计和制造,适用于需要稳定电源的各种工业应用。

TIS 600-124 工业电源产品图片展示

TIS 600-124 (5).jpg

TIS 600-124 工业电源视频展示

TIS 600-124 工业电源特点和注意事项

特点:

功率输出:TIS 600-124能够提供高达600瓦的功率输出,电压为12伏特或24伏特(此处提到的是24伏特版本),电流输出可达24安培。
安装方式:该电源采用DIN导轨安装方式,方便在控制柜或工业现场安装。
低纹波和噪声:电源具有非常低的纹波和噪声水平,这对于敏感电子设备和精密控制应用至关重要。
电磁兼容性:符合EN61000-6-3和EN61000-6-4的电磁干扰(EMI)标准,意味着它可以在电磁干扰较高的工业环境中正常工作,同时不会对周边设备造成干扰。
抗干扰能力:具有高度的抗电气干扰能力,能够在恶劣的工业环境中为敏感负载提供可靠的电力。
冗余配置选项:TIS600-124RED型号提供了冗余电源配置,增加系统的可靠性和可用性,适用于需要高可靠性的工业应用。
可选功能模块:通过使用可选的UDS模块或其他附件,用户可以根据具体的应用需求定制电源的功能,如远程ON/OFF控制、电压调节、电流限制等。
高效和稳定:设计有高效、稳定的电源转换电路,能够在宽泛的输入电压范围内工作,并保持输出稳定。
注意事项:
安装环境:
确保电源安装在通风良好的位置,远离水源和湿气,防止短路和电气危险。
避免安装在极端温度条件下,电源应在指定的温度范围内工作,过热或过冷都可能影响性能和寿命。
将电源安装在无尘或少尘的环境中,过多的尘埃会堵塞散热通道,导致过热。
电气安全:
在进行任何安装或维护操作之前,务必断开电源并确保没有残留电压。
使用合适的电缆和连接器,确保所有的电气连接都是牢固的,避免松动导致的电弧或过热。
遵循本地电气规范和标准,如CE、UL、CSA等,进行正确接地和隔离。
输入电压:
核实输入电压范围与电源铭牌上的规格相符,避免过压或欠压导致的损坏。
如果输入电压波动较大,考虑使用稳压器或UPS(不间断电源)以保护电源。
输出负载:
不要超过电源的最大输出功率,以免造成过载和损坏。
监控负载变化,确保电源在安全范围内工作。
维护和检查:
定期检查电源的通风孔是否被阻塞,清理灰尘和异物。
检查连接端子是否有腐蚀或松动,及时紧固或更换。
定期进行电气测试,检查绝缘电阻和功能完整性。
操作和编程:
参考用户手册进行电源的设置和编程,确保所有功能正确配置。
如果电源支持远程监控或控制,确保网络连接安全,防止未经授权的访问。
环境兼容性:
确认电源符合工作环境的电磁兼容性(EMC)要求,避免对其他设备产生干扰。
在存在电磁干扰的环境中,采取适当的屏蔽和滤波措施。
备用和冗余:
如果电源是关键系统的一部分,考虑使用冗余配置,如TIS 600-124RED型号,以提高系统的可靠性和可用性。

Features:

Power output: TIS 600-124 can provide up to 600 watts of power output, with voltages of 12 volts or 24 volts (referred to here as the 24 volt version), and a current output of up to 24 amperes.

Installation method: The power supply adopts a DIN rail installation method, which is convenient for installation in control cabinets or industrial sites.

Low ripple and noise: Power supplies have very low levels of ripple and noise, which are crucial for sensitive electronic devices and precision control applications.

Electromagnetic compatibility: Complies with the electromagnetic interference (EMI) standards of EN61000-6-3 and EN61000-6-4, which means it can operate normally in industrial environments with high electromagnetic interference without causing interference to surrounding equipment.

Anti interference capability: With high resistance to electrical interference, it can provide reliable power for sensitive loads in harsh industrial environments.

Redundant configuration options: The TIS600-124RED model provides redundant power supply configuration, increasing system reliability and availability, suitable for industrial applications that require high reliability.

Optional functional modules: By using optional UDS modules or other accessories, users can customize the power supply's functions according to specific application requirements, such as remote ON/OFF control, voltage regulation, current limitation, etc.

Efficient and Stable: Designed with an efficient and stable power conversion circuit, it can operate over a wide range of input voltages and maintain stable output.

Notes:

Installation environment:

Ensure that the power supply is installed in a well ventilated location, away from water sources and moisture, to prevent short circuits and electrical hazards.

Avoid installation under extreme temperature conditions. The power supply should operate within the specified temperature range, as overheating or undercooling may affect performance and lifespan.

Install the power supply in a dust-free or low dust environment, as excessive dust can block the cooling channels and cause overheating.

Electrical safety:

Before carrying out any installation or maintenance operations, be sure to disconnect the power and ensure that there is no residual voltage.

Use appropriate cables and connectors to ensure that all electrical connections are secure and avoid arcing or overheating caused by looseness.

Follow local electrical regulations and standards such as CE, UL, CSA, etc. for proper grounding and isolation.

Input voltage:

Verify that the input voltage range matches the specifications on the power nameplate to avoid damage caused by overvoltage or undervoltage.

If the input voltage fluctuates significantly, consider using a voltage regulator or UPS (uninterruptible power supply) to protect the power supply.

Output load:

Do not exceed the maximum output power of the power supply to avoid overload and damage.

Monitor load changes to ensure that the power supply operates within a safe range.

Maintenance and Inspection:

Regularly check if the ventilation holes of the power supply are blocked, and clean dust and foreign objects.

Check if the connecting terminals are corroded or loose, and tighten or replace them in a timely manner.

Regularly conduct electrical tests to check insulation resistance and functional integrity.

Operation and programming:

Refer to the user manual for power settings and programming, ensuring that all functions are configured correctly.

If the power supply supports remote monitoring or control, ensure network connection security and prevent unauthorized access.

Environmental compatibility:

Confirm that the power supply meets the electromagnetic compatibility (EMC) requirements of the working environment to avoid interference with other devices.

Take appropriate shielding and filtering measures in environments with electromagnetic interference.

Backup and redundancy:

If the power supply is part of a critical system, consider using redundant configurations, such as the TIS 600-124RED model, to improve system reliability and availability.

TIS 600-124 工业电源相关产品推荐


YAMATAKE EST0240Z05WBX00模块MTL831B 温度转换器
PSR-53-7 变频伺服模块MVAJ27T1FB0784D模块


推荐资讯

+86 15270269218